Mahogany Teakwood Candle Recipe

This marbled pillar candle showcases flowing colors that blend seamlessly, creating a one-of-a-kind piece of fun...

This marbled pillar candle showcases flowing colors that blend seamlessly, creating a one-of-a-kind piece of functional art.

Shopping List

Pillar of Bliss Wax

10 lb

Round Pillar Candle Mold

51-32-18 Zinc Core Candle Wicks - 7 inch

100 pc

NG Mahogany Teakwood Type Fragrance Oil

Ivory Nature Friendly Liquid Candle Dye

1 oz

Cinnamon Nature Friendly Liquid Candle Dye

1 oz

Brown Nature Friendly Liquid Candle Dye

1 oz

Gingerbread Nature Friendly Liquid Candle Dye

1 oz

Directions

Step 1

Prepare your molds. You will need both the 3 x 4.5 inch round pillar mold. Place a wick through the hole in the bottom of each of the molds. Then, you can place a plug in the bottom of the mold. Alternatively, you can use hot glue to completely seal the hole.

Step 2

Now, weigh out and melt 475 grams of the Pillar of Bliss Candle Wax. Melt the wax using a double boiler.

Step 3

Once melted, add two drops of the ivory candle dye. Stir.

Step 4

Now, add the NG Mahogany Teakwood Type Fragrance Oil. Once again, stir.

Step 5

Pour the wax into the molds leaving about for the second pour, if needed.

Step 6

When the wax has setup, but is still warm, poke relief holes.

Step 7

Reheat the remaining wax and pour it into the molds.

Step 8

Once the candles have setup, remove it from the mold.

Step 9

Fill the clean pouring pot with water. You should fill it about halfway. Then, place a couple drops of the cinnamon, brown, and gingerbread candle dye. Holding the wick, dip the candle in the water. Pull it out and set it on your pan to dry. The dry time will depend on how thick the liquid candle dye is on the candle. We let ours set for about 5 days.

To Use

Let the candle cure for at least 48 hours. Trim your wick to 1/4" before burning.

General

Tags: Candles

Recipe Ingredients

Equipment From Home

Pots (for double boiler)
Water
Mixing Spoons
Pan Lined with Wax Paper

Directions

Prepare your molds. You will need both the 3 x 4.5 inch round pillar mold. Place a wick through the hole in the bottom of each of the molds. Then, you can place a plug in the bottom of the mold. Alternatively, you can use hot glue to completely seal the hole.

Now, weigh out and melt 475 grams of the Pillar of Bliss Candle Wax. Melt the wax using a double boiler.

Once melted, add two drops of the ivory candle dye. Stir.

Now, add the NG Mahogany Teakwood Type Fragrance Oil. Once again, stir.

Pour the wax into the molds leaving about for the second pour, if needed.

When the wax has setup, but is still warm, poke relief holes.

Reheat the remaining wax and pour it into the molds.

Once the candles have setup, remove it from the mold.

Fill the clean pouring pot with water. You should fill it about halfway. Then, place a couple drops of the cinnamon, brown, and gingerbread candle dye. Holding the wick, dip the candle in the water. Pull it out and set it on your pan to dry. The dry time will depend on how thick the liquid candle dye is on the candle. We let ours set for about 5 days.

To Use

Let the candle cure for at least 48 hours. Trim your wick to 1/4" before burning.

General

Natures Garden is not responsible for the performance of any of the recipes provided on our website. Testing is your responsibility. If you plan to resell any recipes we provide, it is your responsibility to adhere to all FDA regulations if applicable. If there are ingredients listed in a recipe that Natures Garden does not sell, we cannot offer any advice on where to purchase those ingredients. We also do not offer any advice on formulating or altering recipes.